Loading...
1.1 This test method covers and provides a measure of the resistance of a graphite to crack extension at ambient temperature and atmosphere expressed in terms of stress-intensity factor, K, and strain energy release rate, G. These crack growth resistance properties are determined using beam test specimens with a straight-through sharp machined V-notch.
1.2 This test method determines the stress intensity factor, K, from applied force and gross specimen deflection measured away from the crack tip. The stress intensity factor calculated at the maximum applied load is denoted as fracture toughness, KIc, and is known as the critical stress intensity factor. If the resolution of the deflection gauge is sensitive to fracture behavior in the test specimen and can provide a measure of the specimen compliance, strain energy release rate, G, can be determined as a function of crack extension.
1.3 This test method is applicable to a variety of grades of graphite which exhibit different types of resistance to crack growth, such as growth at constant stress intensity (strain energy release rate), or growth with increasing stress intensity (strain energy release rate), or growth with decreasing stress intensity (strain energy release rate). It is generally recognized that because of the inhomogeneous microstructure of graphite, the general behavior will exhibit a mixture of all three during the test. The crack resistance behavior exhibited in the test is usually referred to as an “R-curve.”
Note 1: One difference between the procedure in this test method and test methods such as Test Method E399, which measure fracture toughness, KIc, by one set of specific operational procedures, is that Test Method E399 focuses on the start of crack extension from a fatigue precrack for metallic materials. This test method for graphite makes use of a machined notch with sharp cracking at the root of the notch because of the nature of graphite. Therefore, fracture toughness values determined with this method may not be interchanged with KIc as defined in Test Method E399.
1.4 This test method gives fracture toughness values, KIc and critical strain energy release rate, GIc for specific conditions of environment, deformation rate, and temperature. Fracture toughness values for a graphite grade can be functions of environment, deformation rate, and temperature.
1.5 This test method is divided into two major parts. The first major part is the main body of the standard, which provides general information on the test method, the applicability to materials comparison and qualification, and requirements and recommendations for fracture toughness testing. The second major part is composed of annexes, which provide information related to test apparatus and test specimen geometry.
| Main Body | Section |
| Scope | 1 |
| Referenced Documents | 2 |
| Terminology | 3 |
| Summary of Test Method | 4 |
| Significance and Use | 5 |
| Apparatus | 6 |
| Test Specimen | 7 |
| Procedure | 8 |
| Specimen Dryness | 9 |
| Calculation of Results | 10 |
| Report | 11 |
| Precision and Bias | 12 |
| Keywords | 13 |
| Annex | Annex A1 |
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.6.1 Measurement units expressed in these test methods are in accordance with IEEE/ASTM SI 10.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
5.1 This test method may be used for guidance for material development to improve toughness, material comparison, quality assessment, and characterization.
5.2 The fracture toughness value provides information on the initiation of fracture in graphite containing a straight-through notch; the information on stress intensity factor beyond fracture toughness as a function of crack extension provides information on the crack propagation resistance once a fracture crack has been initiated to propagate through the test specimen.
| SDO | ASTM: ASTM International |
| Document Number | D7779 |
| Publication Date | Oct. 1, 2020 |
| Language | en - English |
| Page Count | 9 |
| Revision Level | 20 |
| Supercedes | |
| Committee | D02.F0 |
We're glad to see you again! Please enter your email and password to continue
Need an account?
Register for an account to join our community! Gain access to exclusive content, participate in discussions, and stay updated on the latest news.
Have an account?
Forgot your password? No worries! Please enter your email to reset your password. If your email exists in our system, you will receive a password reset link.
Have an account?
We've sent an email to reset your password if an account with that email exists. Please check your inbox and follow the instructions in the email. If you don't see the email, please check your spam folder.
We have sent a verification email to you. Please check your inbox and follow the instructions in the email to verify your account. If you don't see the email, please check your spam folder.